EP model replacement gearbox for woods rotary gearbox

NEW forty HP GEARBOX Smooth Input 1 three/eight 12 spline output Interchangable with market well-known dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Numerous A lot more

Functions
(one) brand new 45 horse electrical power shearpin gearbox. This gearbox matches numerous different can make of 4′,5′ and some 6′ rotary cutters. I promote a good deal of these containers each calendar year for many distinct programs and carry ALL Substitute Parts for this box, but ideally you won’t have to fear about that.
Here are the specs on the box:
*forty five horse power gearbox
*Common 1-3/8″ smooth enter shaft(where the pto shaft hooks on). The pto shaft is held on by a one/2 shearbolt.
*size of the input shaft out of the gearbox is three” lengthy
*bolt hole pattern for mounting is on the corners, four-3/4 center of gap to middle of gap. It takes a 5/eight” bolt.
*12 splined output shaft(the place the blade carrier hooks up on the base)
*1-9/16 exterior measurement more than the output shaft splines- from the foundation of the output cap to the finish of the splines is two-three/four” long- overall size of the output shaft is four-one/2″ long.
*takes a one” threaded castle nut and a carter essential on the bottom of the output shaft to protected blade pan(NUT is included – – BLADE PAN IS NOT!!)
*overall top of the box from the leading of the mower deck to the best of the box is nine-one/two”
This is a pretty heavy merchandise (forty seven lbs.) so freight is not cheap, but we do not make anything off of freight, what ever ups expenses us we cost you.
40 HP
one:1:47 Ratio
one-3/8″ Sleek Input Shaft with Shear Pin Gap
one-one/2″ twelve-Spline Ouput Shaft
Bolt Pattern: 6-one/2″ (4) five/8″ Holes, five” Middle Hole Essential for Shaft Assembly
The Input and Output Shafts Can not be Bought Serparately.
They are Bought as a package.
The kit contains the following areas: enter shaft, input gear, output shaft, output equipment.
The Shaft Kit Are not able to Be Separated.

EP model substitute gearbox for woods rotary gearbox

Rotary Cutter Gearbox Troubleshooting Guide
Is your mower leaking, creaking or otherwise executing incorrectly? You’ve arrive to the right spot.

Read through underneath for the most widespread troubles with rotary cutter gearboxes and their options (from rapid and filthy, to expert).

Leaking Base Seal:
If you have wrapped some baling or fencing wire all around your output shaft and blown the seal, the specialist issue to do is to exchange the seal.
If your output seal is intact, and you are in a position to get ID, OD and thickness measurements (in millimeters), most bearing properties can purchase you up a generic double-lip seal that will get you back up-and-managing. If not, give us a phone and we can help you type out what you need to have.
A dental pick is the easiest way to get rid of the aged seal prior to pressing in the new one particular.
If you’re fortunate ample to have a slow-leak, the swift and soiled approach is to run automotive-sort grease in the gearbox right up until the new seal will come in. Be sure to check out and include grease far more frequently than you would with oil, as this is NOT a expert repair.

Broken Output Shaft:
Uh oh. You strike something that didn’t move. The great information is that the output shaft on most gearboxes is reasonably simple to change. The undesirable news is… it is hardly ever an isolated failure.
The initial thing to do is to just take aside your gearbox and evaluate the full extent of the injury. If it is actually just the output shaft, you should be in a position to adjust it out, no dilemma. The output shafts start at about $70 and go up in price tag relying on the dimensions of the gearbox.
Nevertheless, in most situations, the bearings ($20/ea), seals ($10/ea) and gear-established ($70) will also usually take a beating. If you might be unlucky, the output cap ($80) will also suffer some damage.
In this circumstance, it is normally less expensive to change the gearbox. Examine the price of elements to the cost of an complete, new, warrantied gearbox. Sometimes, even experts have to know when to call it a working day.

I Want to Adjust my Input Shaft:
If you are tired of modifying shear pins or searching back again and observing that your mower has not been chopping, you may want to install a slip-clutch pto shaft (Indeed, we market individuals too).
This normally demands setting up a 540-fashion, 6-spline enter shaft ($eighty five) on your mower’s gearbox.
Blessed for you, we did a create-up on our weblog. It is called “How to alter the input shaft on your rotary cutter gearbox”.

My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem kind-of equivalent over-the-mobile phone. The best factor to do is to disassemble your gearbox and consider a look at the gears and bearings. The concern will usually existing by itself in the way of broken/missing equipment tooth, toasted gears (like that photo on our house webpage), or blown bearings.
If every thing appears normal, consider modifying the equipment-mesh. This is done with the mylar “gaskets” that sit in between the major gearbox situation and the enter/output caps. Try incorporating or getting rid of some of these spacers till your gears have roughly one/8″-one/4″ of cost-free enjoy. Pros can order replacements ($1-2) in different thicknesses, but we advocate the quick and dirty method of slicing your possess out of a sheet of mylar.
Do not overlook to re-seal the gearbox with RTV after you’ve located the right blend. Even even though they are referred to as “gaskets”, they will not seal your gearbox on their own.

Have you attempted Gearbox For Dusters? Make certain to visit our website and discover out more.