Cycloidal pinwheel reducer is certainly a up-dated of fresh type transmissing machine made with K-H-V less tooth engagement and the cycloidal pin wheel clenching device, which are widely used in drive and reducing of textile and dying, foodstuff, mining and metallurgy, Essential oil and chemical job machinery etc, conveyors, cranes and Industry. various fields.

1. Gear is made of high power low carbon alloy metal by carburizing and quenching. The hardness of tooth area can reach HRC58-62. CNC grinding technology is used for all with high accuracy, gears and good contact performance
2. high transmission productivity: single stage over 96.5%; double stage over 93%; three stage over 90%;
3. stable procedure and low noise;
4, compact structure, light-weight, long service life and high bearing capability;
5. convenient to assemble, check and disassemble.

Operation specifications and precautions
1.High modularization design: various equip with various electric motor or other power suggestions conveniently.Same machine type may equip with numerous power motor. It really is easy to know the combination and
junction between every equipment type.
2.Transmission ratio: great division, wide scope. The combined machine type may form very large transmission ratio, i.e. outcome suprisingly low rotary speed.
3.Form of unit installation: the position to be installed isn’t limited.
4.High strength, compact: the box body is made of excessive strength cast iron. Gear and equipment shaft adapts the gas carbonization, quenching and good grinding process, therefore the bearing ability of unitvolume is excessive.
5.Long life: Beneath the condition of right type chosen (including choosing suited operation parameters)normal operation and maintenance, the life of main elements of speed reducer (except sporting parts) should not be significantly less than 20000 hours. The putting on parts include lubricating bearing, oil and oil seal.
6.Low noise: because main elements of speed reducer are processed, assembled and tested critically,therefore the noise of speed reducer is normally low;
7.Parallel axis -bevel wheel speed-down motor
cycloidal gear reducer

1. High velocity ratio and efficiency
Single stage transmission may reach to at least one 1:87 of speed-downward ratio and the efficiency is certainly more than 90%. If work with multi-speed get the speed-down ratio is bigger.
2. Compact
Being adapted epicyclic transmitting principle, the input and output shaft are at same axis center, it is compact.
3. Smooth and steady run and low noise
The cycloidal pinwheel has more meshed teeth, the overlapping coefficient id big and the device part is stable, the vibration and noise is limited at the minimum content.
1. Large deceleration ratio
A high deceleration ratio of 1/30-1/320 can be acquired.The structure is simple, but it can know high reduction ratio gadget.
2. Small gear clearance
The Get, which meshes with ordinary gears and has minimal backlash, is vital to the controller business.
3. High precision
Multiple teeth are engaged concurrently, and there are two gears engaged with 180 degree symmetry. Accordingly, the affect of tooth pitch mistake and cumulative tooth pitch mistake on the rotation accuracy is relatively average, making the position precision and rotation accuracy reach a very high level.
4. Less parts, convenient installation
The three basic parts achieve a higher deceleration ratio, plus they are all on a single axis, therefore the kit is easy to install and easy to shape.
5. Small in size and light in weight
Compared with the previous gear device, the quantity is 1/3, the fat is 1/2, but can obtain the same torque potential and reduction ratio, obtaining small lightweight.
6 High torque capacity
Flexible wheel material USES unique steel with huge fatigue strength.Not the same as ordinary transmission unit, the amount of teeth meshing makes up about in regards to 30% of the full total amount of teeth. Additionally, it is in call with the surface, to ensure that the pressure borne by each equipment is reduced and high torque potential can be obtained.
7 High efficiency
The sliding of gear meshing parts is quite small, which reduces the energy loss caused by friction. Therefore, high reduction ratio can be achieved while maintaining high proficiency, and miniaturization of traveling motor can be realized.
8. Low noise
The gear meshing cycle acceleration is low, the transmission movements force balance, which means operation is quiet, and the vibration is very small.
◆Excessive speed ratio and great efficiency single-stage transmission can perform a deceleration ratio of 1 1:87, and the efficiency is a lot more than 90%. If multi-stage transmission can be used, the deceleration ratio will become larger.
◆Because planetary transmission basic principle is adopted, the suggestions shaft and result shaft are on a single axis line, so that the machine model can get the smallest possible size.
◆The number of meshing teeth of cycloidal needle teeth with smooth running noise and low cycloidal noise is more, the overlap coefficient is larger, and the mechanism of balancing machine parts produces the vibration and voice limited by a minimum.
◆Reliable use and prolonged service life as the key parts are created from high carbon chromium steel, high strength is usually obtained by quenching (HRC58-62), and rolling friction is used in a few transmission contacts, therefore the service life is very long.
Cycloid reducer is definitely a cycloid needle teeth meshing planetary transmission principle drive models, is an ideal transmission has many advantages, versatile, and may be both negative and positive operation.

•Big ratio, and high efficiency Smooth operation,

• low noise The utilization of reliable,

• extended life can reach 50000 hours

• Main parts high-carbon the Ming-metal after quenching treatment (HRC58-62),

• operation and contact with rolling friction, basically very little wear, durable.

• Compact structure,

• tiny size Because the usage of a planetary transmitting, the type shaft and the output shaft on a single axis, which makes the model to get the smallest possible size.

• Reasonable design, easy protection, and break down easily install,

• minimal number of parts and also simple lubrication, cycloid reducer trusted by the user.
(1)Size above PL/PF120(including)high torque products adopt integral double wall world pinion precision, increase the output strength and carrier.

(2).Hoop clamp coupling have five connection ways suited to different application environments.

(3).Size over PL/PF120(incorporating)precision and high strength integral inner gear housing, processed in a single station,which remove the cumulative error and assembling mistake of split type.Remove casting process;adopt incredibly hot of forging process, that will reduce the blank material defects.

(4).The meshing gear adopt shaving procedure after carburizing and quenching,which simpler to make gear surface area smooth and high accuracy,reduce the temperature rising caused by gear area gluing and friction.
This series worm-gear reducer was designed after RV worm microreducer, which have a complete norm, wide speed for selection, and many mounting positions. Its efficiency and mounting dime nsions conform the same sorts of foreign.
The mixture of worm and gear has higher efficiency and wider speed range to single worm.
Designation of square shape, compact structure, radiate heat efficiently, beautiful condition and low noise.
Good sealing and adaptability.Its blend with T equipment reducer and MB/MBN variator may meet a myriad of speed requirement.