The EP Series Helical Bevel Reducer provides unmatched performance, durability, and style flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-motor system. Cat4CAD supports you in selecting and configuring these products, provides you the opportunity to print out intensive technical data bedding, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty class F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Essential gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric result shafts, mounting pilots and flanges provide a wide selection of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal installation on five sides or via a torque arm.
Worldwide Engine: Multiple leads and windings for worldwide multi volt/Hz requirements plus modular design to simply accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals on heat treated, plunge floor shafts
Shaft mounting options include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It is offered as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors are available in three phase high efficiency styles through 50 HP and single phase to 5 HP. We offer a variety of input and result shaft choices. Additionally, you will find fixed and variable acceleration motors and range of ratios available in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Vital dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
DURABLE Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying needs of customers, we offer an array of Helical Bevel Gear Reducers. The technological articles of our products permits an extraordinary efficiency/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully used in a vast number of commercial and civil applications. 
They are B-Series units that offer excellent affordability and output torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with compact motor, PB-fitted for motor coupling with flexible joint
Casing with feet FC, flange SC and common UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 decrease stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to ensure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue helical bevel gear reducer epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced output, assemble/disassemble kit
Series EP right angle helical bevel equipment motors provide ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five levels. Motors can be found up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and will be offered with single or dual extended output shafts.
Devices are also available because shaft mounted or with output flanges and are designed for mounting horizontally or vertically. The models can also be provided with a bolt on torque reaction bracket and all variants can be found either motorised or with an insight shaft assembly.
Adding to the brand new selection of Ever-Power helical equipment motors this product takes benefit of our a long time of accumulated design expertise together with the use of high quality materials and components. The end result is a series of acceleration reducing geared motors providing high load carrying capacities, increased efficiency, quiet running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double oil seals, on insight and output shaft as required.
All systems are dimensionally interchangeable with various other major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be installed with a backstop module and reducer Systems can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemical substances, pharma, packaging, food processing, plastic-type and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for engine coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Power up to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and made up of Y series engine, helical gear,Arc gear and worm gear. The gears are made of high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, nice appearance ,and strong capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The effectiveness is up to because high since 96% with low energy usage, strong adaptability and is with the capacity of functioning continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.
